Acroprint TQ600F Bedienungsanleitung

TQ600F Face Recognition Terminal User Manual

6 1.7 Verification Modes 1.7.1 Face Verification 1: N Face Verification The terminal compares the current face template (image) with all face templat

71.7.2 Password Verification In the password verification mode, the device compares the password entered with the password assigned to the user ID.

8Badge + Facial Verification • Swipe your badge over the swipe area to enter the 1:1 facial verification mode. • Scan your face using the proper t

9FACE & PW verification: Users can punch in/out by scanning their face. Once their face has been verified they are prompted to enter their pass

10PW & RF verification: Users can punch in/out using their Pin#/Password and proximity badge. Press “1:1” on the Main Interface. Users can pu

112. Main Menu There are two types of users: Ordinary users and Administrators. Ordinary users are only granted the rights of face, password or card

12Auto Test: Test operational status of various hardware components including the display, voice prompts, camera, keyboard screen, clock (time) tes

133. Add User Press [Add] on the User Mgt. screen to display the Add User screen as shown to the right. • User ID: Enter a user ID. 1 to 9 digit u

143.2 Entering a Name • Press [Name] on the Add User screen to display the name input screen with keyboard. • On the displayed keyboard, enter a us

15• After the password is entered, a screen is displayed as shown to the right. Press [Save] to save the current information and return to the pre

IImportant Claim Thank you for purchasing the TQ600F Face Recognition Terminal. Before installing your terminal please read this manual carefully

16• If your face image is enrolled successfully, the system will display a prompt message and automatically return to the Add User screen. • Press

173.7 Enroll Photo If you enrolled your photo in the system, the system will display your enrolled photo in addition to your ID and name after you p

184. User Management Press [User Mgt] on the main menu screen to display the user management screen. Users are listed in alphabetical order by last

194.2 Delete a User On the User Info screen, you can delete all or partial user information. • Press [Delete] to delete a user. • On the displayed

205. Communication Settings You can set related parameters for the communication between the device and PC, including the IP address, Subnet Mask, G

216. System Settings Through the System menu, you can set system-related parameters, including General Settings, Display Settings, Face, Log setting

226.3 Face Parameters • 1: 1 Threshold: Used to set the threshold of matching between the current face and the face template enrolled in the device

236.4 Log Settings • Log Alert: When the available space is insufficient to store the specified number of attendance records, the device will autom

24• To configure the Status function, press Status on the Function screen. The Edit screen will appear, allowing the user to configure individual s

256.6 Update You can upgrade the device firmware by using an upgrade file stored on a USB Flash Drive. Note: If you need a firmware

II Table of Contents 1. Instructions for Use ...

26 7. Data Management Through the [Data Mgt.] menu, you can perform management of data stored on the device, for example, delete attendance records,

277.2 SMS Administrators can write a short message to be displayed on the terminal screen during a designated period. Short messages are classified

28• Press Start or Valid to start the configuration screen shown in the following figures: • Press the number key to input values to be set,

29• Press Done to save the settings and return to the previous screen. Press Save to store the short message and go back to the previous screen. The

307.2.2 View a Short Message View a public short message On the initial screen, public short messages are automatically displayed on the minutes. Al

31 7.3 Work Code Note: If using timeQplus software, work codes with labels are defined in the software and are then uploaded to the terminal. DO NOT

328. Date/Time Setting 8.1 Set Date/Time The date and time of the device must be set accurately to ensure the accuracy of attendance time. • Press [

33• Press [Bell] on the Date/Time screen. The displayed bell setting screen lists all the predefined bells. • Press a bell in the list on the bell

34• Press [None] to display the DLST mode selection screen. The available options are Mode 1, Mode 2 and None. • Select the DLST mode; you will aut

359. Auto Test The auto test enables the system to automatically test whether functions of various modules are normal, including the screen, sensor,

III 6. System Settings ... 21

36 10. USB Disk Management Through the [Dn/Upload] menu, you can download user information and attendance data stored to a USB disk to be uploaded to

37 11. System Information You can check the storage status as well as version information of the device through the [Sys Info] option. • Records: Th

38 12. Appendix 12.1 Entering Text Using the Keyboard The device has a full QWERTY keyboard that supports upper and lower case Alpha characters, numb

39 • After finishing the entry of name, press [X] to exit the Keyboard Interface and return to the previous screen. 12.2 Photo ID Fu

40 12.3 Multi-combination Authentication Mode Four elements can be combined to authenticate a user: User Number (PIN#), Face (FACE), Password (PW) an

41 06-0405-000 Rev. A

11. Instructions for Use 1.1 Standing Position, Posture and Face Expressions 1. Recommended standing-distance from device: It is recommended that us

2 1.3 Use of the Touch Screen Touch the screen with one of your fingertips or the edge of a fingernail, as shown in the following figure. A broad p

3 • Enter Text: Press the [Name] key. The system will automatically display the keyboard. After entering the user name, press [X] to save and retur

4LED Indicator Touch Screen Touch keys Camera ID Card Swipe Area 1.5 Appearance of Device (1) Front View (2) Side View USB Port Reset Button

51.6 Main Interface • Date: The current date is displayed. • Screen Shortcut Key: Press the shortcut key to display the WorkCode